PRP Kit (10-Pack)


This is a pack of 10 Dr PRP tube kits. Each DrPRP tube also comes with it's own anticoagulant.

Dr.PRP is a medical kit designed for fast & efficient PRP separation. With this, you’ll get perfect concentration of Platelet Rich Plasma (PRP) every time you use it. So for consistently efficient PRP treatments with faster results, you can count on Dr. PRP’s patented one-step platelet separation kit.

SKU: DRPRP-PRP-002 Category: Tags: , ,


With Dr. PRP Platelet separation kit, it’s easy to collect your patient’s blood and turn it into highly concentrated (platelet-rich) plasma. Dr.PRP uses a simple, innovative design to efficiently capture the majority of the patient’s platelets. Click the button below to watch video now.

Accelerated Natural Healing With PRP

With Dr. PRP Platelet separation kit, it’s easy to collect your patient’s blood and turn it into highly concentrated (platelet-rich) plasma. Dr.PRP uses a simple, patented design to efficiently captures the majority of the patient’s platelets.

The blood samples taken from the patient are transferred to Dr. PRP kit for Platelet separation using a centrifuge. The final compoents of the blood will be the red blood cells, the platelets, and the plasma.

When platelets become activated, growth factors are released and initiate the body’s natural healing response.

97% Platelet Recovery Rate

Platelet concentration determines the efficiency of a good PRP separation system regardless of the volume of Platelet Rich Plasma (PRP) produced. Dr. PRP uses a specific filter and a recommended centrifuge speed to achieve a high platelet recovery rate of 97% or more (platelet counts up to 2,000,000 per µl of blood.)

Growth Factors In Platelets

Platelet Derived Growth Factor (PDGF-aa, PDGF-ab, PDGF-bb)

– Stimulates cell replication
– Promotes angiogenesis
– Promotes epithelialisation
– Promotes granulation tissue formation

Transforming Growth Factor (TGF-ß1, TGF-ß2)

– Promotes formation of extracellular matrix
– Regulates bone cellmetabolism

Vascular Endothelial Growth Factor (VEGF)

– Promotes angiogenesis

Epidermal Growth Factor (EGF)

– Promotes cell differentiation and stimulates
– Re-epithelialisation, angiogenesis and collagenase activity

Fibroblast Growth Factor (FGF)

– Promotes proliferation of endothelial cells and fibroblasts
– Stimulation of angiogenesis

The higher the platelet recovery, the more concentrated the platelets which leads to more faster healing for your patients.”

How To Use Dr. PRP For Platelet Separation

In a 20 cc syringe take 2 cc of anticoagulant, then draw 18cc of blood from a subject (final volme : 20 cc).

Inject the drawn blood to Dr.PRP kit through the upper injection port until the blood level reaches the 20cc scale marked on the kit. (For easier injection, tilt the kit)

- Separate the plasma layer and red blood cell (RBC) layer by the first centrifugation. (Prior to centrifugation, balance the weight of kit with counterbalance)

- Conditions for the First Centrifugation (RPM) Female - 3,000 RPM 3 minutes Male - 3,000 RPM 4 minutes When fail the seperation - 3,000 RPM 1 minutes *For subjects taking aspirin, antihypertensive drugs, with cardiac disease, anemia, or during menstruation, the centrifugation should be done for 4 min at 1,000 RCF.

After the first centrifugation, identify the separation position of the plasma and the RBC layer. Then adjust the height of the separated boundary to the indicated point by pushing up or pulling down the adjusting knob located at the lower part of the Kit. (If the volume of the plasma layer or the separation is not quite well done, additional centrifugation may be done for about 1-2 min at same RPM)

In order to block the plasma and the RBC layer completely, fasten the adjusting knob (counter-clockwise) located at the lower part of the Kit. Then fasten the valve(counter-clockwise) just above the adjusting knob. Finally fasten the adjusting knob(counter-clockwise) again.

Put the fastened PRP Kit to the centrifuge with counterbalance for the second centrifugation to enrich the concentrated platelet. *Condition for the second centrifugation : 6 min at 3,200 RPM

Place the PRP Kit in its upright position with care in order to prevent mixing of the separated PRP and PPP. Open the upper sillicone lid on the Kit. Using a 10cc syringe with a long needle (> 5 cm) take out the PPP layer slowly from the upper part leaving 4 cc at the base.

Shake and mix the remaining 4 cc of the PRP layer. Then administrate the PRP.

Suggested Reading